The Classic Accessories Stellex V-Hull Fishing Boat Cover # CA20144 is designed to fit snuggly on a 12'-14' v-hull boat. The width of the boat should not exceed 68" at the widest point. You want the cover to fit snug so that any wind that hits the boat will not allow the cover to move and possibly chafe, creating wear or damage to the cover.
For the outboard motor I recommend finding a cover that will encase the entire outboard. This will help prevent any critters from building nests... view full answer...
The Classic Accessories Boat Cover by StormPro # 052963889185 fits 14 -16 foot boats with a beam width up to 75 inches. Since your boat meets those dimensions, the fact that it does not have a windshield is not going to affect how the cover fits. It features an integrated buckle and adjustable strap system as well as an adjustable elastic cord at the bottom of the cover to ensure a tight fit over your boat. view full answer...
Yes, the Taylor Made BoatGuard Eclipse V-Hull Bay Boat Cover # 36970914 will fit your 22' V-Hull boat with 96" beam. This cover will fit boats between 20' - 22' and beams up to 102" (maximum width), so it will still work for your 96" beam. It is designed to be trailable and has elastic cords to help keep the cover tight. view full answer...
To determine if this Classic Accessories Boat Cover # 052963889482 will fit on your 2002 Fourwinns Horizon 180 you will need to take some measurements of your boat.
This cover is designed to fit boats that are 17 to 19 feet in length and boats with beam widths up to 102 inches.
If you measure the length and width of your boat and it fits in those measurements this cover should work for you. If not, email me back with the measurements of your boat and I can hopefully find one that does fit. view full answer...
Yes. You can definitely use the Taylor Made Eclipse Center Console Boat Cover - 17' to 19' Long Boats - 96" Beam # 36970911 on your 16-foot 98 Champion 165 with a center console instead of the # 36970211. However, you may have a bit of extra overhang that can be easily adjusted for a tight fit.
The main difference between the covers is that the # 36970911 is a vented design while the # 36970211 does not include vents that prevent billowing. The # 36970911 also comes with 600-Denier reflective... view full answer...
Your boat at 19 feet and 96 inch beam length is within the tolerances of the Classic Accessories Boat Cover, # 052963889581. As far as width, it fits up to 106 inch wide boats. the extra foot of length should not be a hindrance either.
A similar cover that fits 17 to 19 foot boats and beam widths up to 102 inches is # 052963889482. This would be a tighter fit to your boat. I think the bow rails and the cuddy cabin would necessitate the larger cover though. view full answer...
I do have a solution for you but the cover you referenced Taylor Made Eclipse Pontoon Boat Cover item # 36970912 is not for trailering. I recommend the Classic Accessories StormPro Pontoon Boat Cover item # CA20028, this cover is rated for both storing and hauling your 2015 Suntracker Party Barge 22foot DLX. The cover fits boats from 21' - 24' long and 96" wide at the widest point of boat. view full answer...
I checked the beam width of a number of 18-foot Lund boats and they fall into the range of 88- to 98-inches. Since the Classic Accessories StormPro Boat Cover # 052963889383 fits boat lengths to 18-1/2-feet and beam widths to 98-inches it will work fine on the Lund boat. Since this craft is at the top of the covers size range, and since the cover has an elastic cord in the bottom hem, the fit should be snug and wrinkle-free. view full answer...
I am not 100% sure what measurement you are meaning when you mention a mid line measurement. But the Taylor Made Support Bow for Boat Covers can be installed front to back or side to side in a boat cavity to provide support for the cover to keep it taut, I have included a diagram showing this.
You will just need to measure across the opening area and get the correct sized bow support. These will install using the Taylor Made Support Bow Sockets for Boat Covers # 369935.
We do have these... view full answer...
The BoatBuckle Snap-Lock Boat Cover Tie-Down Straps - 1" x 4' - Qty 6 # IMF14264 uses the basic LBV-1 buckle you are referring to. Although not tested for direct compatibility with other products that is the buckle used so it will fit other products. view full answer...
The Classic Accessories Boat Cover # 052963889482 should have no problem being used with an inboard/outboard motor as long as the dimensions of the boat are compatible with the cover.
This cover is designed for V-hull runabouts that are between 17-19 feet in length and a beam width of up to 102 inches.
I attached installation instructions for you to check out also. view full answer...
I contacted our representative at Classic Accessories and he recommend a Model C Cover, which fits boats 16 feet to 18-1/2 feet long. view full answer...
The Classic Accessories DryGuard Waterproof Boat Cover # CA20085 has 2 straps at the rear of the trailer to help hold it in place. I do recommend getting a Support Pole # 36911981 to help prevent water and dirt from pooling up inside the boat. We do not have any straps which would be able to be used with the cover that would not risk damage to the cover material. view full answer...
The Classic Accessories # CA20028 cover is a universal fit on pontoons that are 21 to 24 feet long and have a beam width of up to 96 inches. You will need to measure the width of your pontoon at the widest point the cover will be required to cover and as long as the measurement is 96 inches or less this cover should work for you.
This cover is appropriate for trailering or for storage. view full answer...
If your 1987 Boston Whaler Montauk is on the lower end of the length range for cover # 052963889383 then the additional slack in the cover will help it fit over the bow and side rails. This cover fits boats that are 16 to 18-1/2 feet long with a beam width up to 98 inches. If your boat is at or near the 18-1/2 foot max length then it could be a tight fit or you would have to go up a size, # 052963889482, which is for 17 to 19 foot long V-hull boats with a 102 inch beam width. view full answer...
As long as your Crown Live is not wider than 106 inches the Classic Accessories Boat Cover by StormPro # 052963889581 is an excellent option as it has a boat length range of 20-22 feet. view full answer...
You can use a Truck/Trailer Tarp # EM57051 as we do not have any covers specifically designed for a boat trailer. This tarp is 12' wide by 24' long and uses a tighter weave than general duty tarps so it will last. It has brass eyelets and steel d-rings making it easy to secure to your trailer with some Bungee Cords # EM06623. view full answer...
Yes, the Classic Accessories boat cover # 052963889185 will work with your 15 foot Sylvan Alaskan as you have described it. The cover is designed for 14 to 16 foot long V-hull boats with a beam up to 75 inches. Your boat is right in the middle of all those specs so you should have a great fit! view full answer...
It looks like the Campion Allante 505 is approximately 16 feet, 7 inches long so you would want to look at covers for 16 to 18-1/2 foot boats such as # 052963889383 or # CA20085.
If your boat is a different length (not counting the outboard motor) let me know. view full answer...
The Classic Accessories DryGuard Waterproof Boat Cover, part # CA20084 would be a good choice for you. The cover fits boats up to 16 feet long and a beam width up to 90 inches. view full answer...